Features

• Provides proper clearance for use with dado sets
• Installs easily using existing table insert screws
• Fits Delta 36-600 table saw

Reviews (2)

A Perfect Fit...
I just bought a Delta TS300 10" table saw (use to be called a model 36-600, by the way) and started looking for dado sets and dado inserts.The Delta website is either perfectly useless or outright wrong when it comes to cataloging the correct accessories for each table saw.So I took my standard insert over to my local tool dealer and asked him to match it up with the correct dado insert.It took him all of 30 seconds to figure it out.
The 34-672 Dado Head Insert is the one to get for the following 10" Delta table saw models: TS300, 36-600, 34-740, and 34-670.
And don't be fooled into buying an 8" dado blade set just because the insert opening is big enough for it.If the motor is less than two horsepower (2 HP), then you should stick with a 6" dado blade set.Anything under 2 HP is considered "underpowered" for an 8" dado.Remember, you now have alot more metal spinning on that arbor, so don't burn out a $... motor just to impress your friends and neighbors.

Bad info on the Delta Web Site
I recently bought a Delta 36-650 10 inch table saw.After looking on the Delta web site, it listed this Dado Insert (34-672) as the correct one for this saw.Well, it was wrong.The correct dado insert for the 36-650 saw is the 34-264 (for 7-8 inch dados), there is a seperate part for 10 inch dado blades.So...I guess I'll be sending this one back...:( ... Read more

Subjects:  1. Saws    2. Table Saws    3. Table Saw Attachments    4. (Tablesaws)   

Features

• Use in place of standard insert to accommodate a 8-inch dado set
• Fits Delta Left Tilt Unisaws for safer use of dado sets
• Installs easily using existing screws for quick set up

Reviews (3)

Expensive
Well, this does work and it fits exactly right.But, be very careful when cutting small parts with a thin dado blade because the workpiece can fall below the insert.

In other words, if you are cutting a 1/4" dado there is a lot of open area where stuff can fall. If you are cutting thin dados, your workpiece should be at least three inches wide, and that still is not very stable.

If you use a your dado blades a lot, I recommend that you create inserts (using zero clearance inserts) for dados between 1/4" and 5/8".I've got two inserts--3/8" and 5/8". The danger of parts falling below the insert is just too high.

And geez, this seems expensive.Zero clearance inserts are about $22 and I think they work better.

YUP
It's smooth and fits well.Pins in ends keep it centered.It's red.It works.Yup...aaayup.

Uuhhh, it fits. And it guards....
What can one really say? It fits well, the slot is nicely slotted, and it does its' blade guarding duties well. Nice adjustment and levelling features. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Editorial Review

Carbide-tipped for longer life, Delta's 8-inch dado head stack fits snugly together to groove impressively smooth square-bottomed slots. The five inside chipper blades allow you the option of cutting dadoes up to 13/16 of an inch wide and as thin as 1/8 of an inch. The blades feature safety shoulders that help control overcutting, thus lessening the chance of kickback, a frequent hazard due to this type of cut's large surface area contact. All dado sets have some antikickback feature; Delta's performs as well as any of them. --Justin Paul ... Read more

Features

• Cuts grooves from, 1/8- to 13/16-inch wide
• Stackable dado set produces square-bottomed dadoes and grooves
• Outer blades have anti-kickback design for safety
• Five inside chipper blades allow dadoes up to 13/16-inch thick
• Anti-kickback design prevents the teeth from cutting too deep for safer cutting

Reviews (10)

Can't Beat the price
Stackable dadoes are the way to go. I get a precision cut. When performing repetitive cuts, setup and cutting time is so much less when using a stackable dadoe vs. a router bit. I've used it to create many drawers and is excellent and convenient for rabbiting work and haven't had a problem.

good dado for the money
i've had this dado set for over a year.i read all the other reviews,boy do some poeple knock it.the first few cuts i made were terrible too. but what i decided to do was buy a real shim kit & throw away that cardboard junk that came with it.shim kits are cheap.since then all the dado's are great.hard wood,soft wood,laminates,ect.also use your head & align the cutters equaly in the gullets of the outer blades,if they are not equally aligned around the blade & the 2 outer blades are not ligned up to each other,you will also have a poor cut.if i had the money to buy the freud super dado i probably would have,but after using this set why bother!!it is just fine.it has produced some beautiful stained cabinets out of oak & cherry.so save your money & get this set!! just remember to toss the cardboard shims!!

Get the Freud instead
I bought this blade a little over a year ago and it's one of the biggest wastes of money that I've ever seen.Cuts through solid wood are only fair but the cuts through plywood leave a lot of tear out and the bottom is uneven and very rough.If you look closely at the picture you will see that there is a small plate attached to the inside of both the outter blades.I though these were a machined on integral part of the blade.NOT!!They are simply glued on as I discovered when one fell off.The quality of construction on this dado is way below par.Spend the extra money and get a Freud or Forrest(if you really have the extra dough).You will not regret it as I now do. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Features

• Built-in width of cut scale for quick set up
• Cuts dadoes and grooves from 1/8" to 13/16"
• Carbide-tipped for long lasting sharpness and durability
• 7" diameter/ 5/8" arbor hole to fit most 10" table saws
• Adjustable for exact sizing of dadoes

Reviews (2)

Saw Arbor Length
I purchased this blade with the purpose of using it on a Delta 10 inch table saw.What I found was that the arbor on my saw was not long enough to accomodate this type of dado blade.Delta should state either the minimum arbor length or model numbers that this blade will work on.In my case I had to go with a 6" stack dado with the maximum cutting width of 1/2".

quick and reliable adjusting dado.
With the delta adjustable dado, changes for cuts are quick, easy and reliable. No "settling for" the measure with the stacked dado. Adjustments are accurate for the cut "needed". Numbered settings, ie, 1/8" to 13/16" are accurate and quickly made. One negative usually associated with adjustable blades , the bevell cut as compared to the squared cut of the stack dado, doesn't exist with the Delta Adjustable. Quality, especially for the price, is outstanding. Carbon tips hold sharp edge through many cuts of hardwoods. I am very satisfied with the Delta Adjustable Dado. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Features

• Use in place of standard insert to accommodate a 6-inch dado set
• Fits Delta Contractor Saws and Right Tilt Unisaws for safer use of dado sets
• Installs easily using existing screws for quick set up

Reviews (4)

does what it says...but
it does what it is suppose to do.but, i regret my purchase.if you have some 1/2" stock laying around make your own and save the money.either jig saw or use a router and trim bit and make a copy of your original insert. get some set screws, tap the holes(for leveling) and you are set.i made mine in about 5 minutes out of mdf. works great and i can make more for different size dado setups.

Dado insert doesn't fit
I purchased the insert with certainty from both Amazon.com and Delta that this is the right insert for my saw.There is only one problem, it is too large to fit in the saw.It is approximately 1/4" too long.In comparing it with the insert that came with the saw it is visibly larger.The only solution appears to be to grind it down as other reviewers have noted on the insert for the 8" Dado sets.While it can be done, it is disappointing for something that should simply drop in.

Its an insert.
What can I say?I laughed. I cried.I cut dados. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Features

• Provides proper clearance for use with a molding cutterhead
• Installs easily using existing table insert screws
• Fits Delta 36-600 table saw

Subjects:  1. Saws    2. Table Saws    3. Table Saw Attachments    4. (Tablesaws)   

Features

• Anti-kickback design for safer cutting of dadoes and grooves
• Carbide-tipped for long lasting sharpness and durability
• Cuts dadoes and grooves from 1/8 to 13/16" wide
• Fits saws with 5/8" arbors

Reviews (2)

Rough cut
This Dado set by Delta produces rough cuts and edges with significant bat wings (.005"-.010" deep). I also had problems with mounting the blades on the arbor (center hole too small).The set is only suitable for general carpentry.

Pretty much works as expected...
This set works well for me.The arbor hole for the right-side blade was a bit tight to fit over the non-treaded portion of my saw's arbor at first, but after a few installations/removals the hole has opened up enough to ease installation.Also, same problem with the chippers; the non-threaded portion of my arbor extends just past the inner face of the right-side blade.Only one of the chippers would fit over this shoulder.I figured out what was wrong, I simply marked that chipper and use it in the same position every time.Other than that, this set works as expected.The smaller size is more suitable for smaller, less powerful saws.I've used this set to cut dados in pine, MDF, oak and cherry with no problems exept for when I accidently mounted one of the chipper backwards.As with any stack dado set, you will probably need to use shims between the chippers to make dados of exact size.This set doesn't include any, but if it did I would give it another star.I like the Veritas shims, since they are color coded for thickness and can be inserted between blades without having to completdly remove the outer blades first. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Features

• Use in place of standard insert to accommodate a 7- or 8-inch dado set
• Fits Delta contractor saws and right tilt unisaws for safer use of dado sets
• Installs easily using existing screws

Reviews (5)

8" Dado Insert
Its delivered to your house and you think that you are now ready to cut dadoes on your table saw, and for making dadoes on large peices of plywood, your right.However, do not be fooled like I was when you think you are ready for all dado cuts with this insert.When you try to cut a more detailed cut such as a tongue and groove joint, where the height of the dado will not be hidden, you will notice that the insert is far from flush with the top of the table, making the height of the cut on smaller peices noticeably inconsistent.To fix this problem, I had to run out to my local hardware store, fork out more of my money to replace the four very small screws that came with the insert, and play with them to get the height flush.The unfortunate part is that these screws have to be just about perfect in length to make this adjustment or the heads of the screws will stick out beyond the countersunk holes.What I would really like to know is how a company with such a reputable name like Delta, can manufacture an insert for its own table saw and still require the consumer to make adjustments like this?Frankly, I am growing tired of building quality furniture with tools that lack the same quality.

Fits a 36-650
It's so hard finding the right part from Delta's site or here. This is the one you need for a Delta 36-650. Some of the other reviewers mentioned having trouble with the fit, mine worked fine.

Insert Doesn't Fit!!!
I own a Delta 10" Professional model table saw.One of the first and most necessary accessories I bought was a dado blade which entailed buying the table insert.After double checking model numbers, etc. to make sure I was buying the right thing, I got it home and it didn't fit.I had to use my angle grinder and quite a bit of time to make it fit.The insert works great now, but it was extremely frustrating having to "custom fit" it to my table saw, especially when the model number was supposed to fit properly. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Features

• Fits Delta Contractor's Saws
• Provides proper support of materials while maintaining proper clearance
• Four set screws provide levelling ability to keep flush with table top
• Convenient finger hole for easy removal

Subjects:  1. Saws    2. Table Saws    3. Table Saw Attachments    4. (Tablesaws)   

Features

• Built-in width of cut scale for quick set up
• Cuts dadoes and grooves from 3/16" to 9/16"
• Carbide-tipped for long lasting sharpness and durability
• 6" diameter/ 5/8" arbor hole to fit most 10" table saws
• Adjustable for exact sizing of dadoes

Reviews (1)

disappointing dado...
I bought this blade because of its relatively low price, compared with other dado blades.Well I believe this is one of those, "you get what you pay for," situations.This blade does not give a very accurate dado cut, often leaving a scalloped cut rather than a square clean cut.Because of the adjustable design, this blade spins at an angle and produces an unacceptable vibration action.If I had it to do over again, I would have spent the extra money and bought a stack type dado blade. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Features

• 6" diameter, 5/8" arbor hole
• Outer blades cut cleanly and smoothly
• Five inner chippers remove the bulk of material
• Cuts dadoes and grooves from 1/8 to 13/16"

Reviews (1)

DON'T GET THIS DADO!!!
I have seen this dado head and I have read about how poorly this dado head cuts. I think That a Thin Rim Dado is much better. But if I were anyone that owns a dado head. I would get the Avemger Products dado sets. They look exactly like the Systi Matic Superfine dado head but they have three things that the Superfine dado head does not. First of all, These sets are available in 6 and 8 inch diameters ranging from 20 to 42 teeth.They also include a 3/32nd inch chipper while Systi Matic does not and you get 8 shims and a manual as well. As far as I'm concerned, The avenger sets look really good to me. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Features

• 6" diameter, 5/8" arbor hole
• Hollow ground outer blades cut cleanly and smoothly
• Five inner chippers remove the bulk of material
• Cuts dadoes and grooves from 1/8 to 13/16"

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)   

Features

• Cuts dadoes and grooves from 1/8" to 1/2"
• Hollow ground outer blades cut cleanly and smoothly
• Fits saws with 5/8" arbors
• Recommended for Delta Bench Saws

Reviews (1)

Nice Dado Cutter for my Delta Bench Saw
This Dado set is exactly what it claims to be.Solid steel and nicely packed.Designed to be used for the Delta Bench Saw and its short arbor, it can only cut dado's up to 1/2 inch.Nicely packaged in a reusable container.The price is right. ... Read more

Subjects:  1. Blades    2. Table Saw Blades    3. Dado    4. (Tablesaws)