Features

• Lifetime warranty
• Fits any saw with a solid cast-iron table top
• Pre-drilled to also fit virtually all 1- to 14-inch table saws
• Flip stop lets the operator choose the necessary measurement
• Can be used on the left or right side

Reviews (7)

Great quality and workmanship.
I just returned from a wood show and saw this sliding table in action.This sliding table tracks straight and level.But most impressive is how strong it is.I put two, 200 pound friends on this table and then moved the table back and forth.The table slid effortlessly, like no one was on the table.It was unbelievable.That's 400 pounds of material moving back and forth.JET makes a sliding table that will attach to most table saws but it is bulky and heavy.This thing is realatively light.The miter is excellent, easy to adjust and very easy to remove.I found that all the functions were well thought out and easy to use.For example:the frame of the sliding table is designed so that when you slide the table towards the rear there are no crossmembers in your way.Meaning that you can move your body inside the front of the table.Thus you don't find yourself leaning over the table as you push the material through.It's attention to detail like this that you will find throughout the design of this table.I would highly recommend this sliding table.

if you have the patiecne...
this thing is a PAIN to adjust, if you are not willing to put in a good day of frustration don't buy it.... but once you do it and you really crank down on the allen bolts it seems to stay put.i set mine up over two years ago and with tons of use it still is right on.
the plastic knobs that are used for moving the fence around are trash... you can find metal replacemnts through some woodworking supply stores (stuff like this can really piss you off when it breaks off while your in the middle of a project)
i pretty much don't use the 49" capacity as it is a pain to move the fence around and change all the adjustments... you can go up to around 34" if you lower the blade and then raise it up through the material, i believe 28"is the real max...
adding a micro adjust stop to the fence would be a nice touch. it is hard to move those 32nd etc...
for all it's short comings i can say i would be lost with out it. it has allowed me to take on some huge projects that would have not been possible crosscutting with a skill saw or what have you.... i don'tconsider it to be expensive, when you start looking into "real" sliding table setups and good panel saws your talking thousands....
i give it 3 stars, a mark that takes in the hassles and cheap knobs and compares it to a powermatic sliding table that costs over $10,000.....

Excalibur Sliding Table
I was looking for a precision attachment for my table saw to cut sheet goods and long stock. The excalibur table is marketed as such a product. Unfortunately, I was very dissappointed. It was an exercise in frustration and futility to properly adjust the unit and once I though I had it, it didn't take much to knock it out of alignment. Sad to say I believe this is a way overpriced piece of equipment (I almost want to say junk)and I believe your money can be better spent elsewhere. I have some ideas of how to correct this but it will require putting more effort than I care to spend on something that cost this much. I wish it was more like my Biesmeyer fence that was able to produce accurate cuts with hardly any difficulty at all. ... Read more

Subjects:  1. Saws    2. Table Saws    3. Outfeed Tables    4. (Tablesaws)   

Features

• Can also display seconds, month, date, time
• Key chain included

Features

• Tool-free installation and removal of splitter plate
• Vertical and lateral adjustment for alignment on saw blade and anti-kickback protection
• Fits General 350 tablesaws

Reviews (9)

Good product with some caveats.
The Merlin splitter, in most ways, is a tremendous improvement over the POS that the factory provides. Setup is not all that difficult. And it is so easy to take on and off the saw! I am much more likely to use the Merlin splitter than I was the factory unit.

The anti-kickback pawls are not as effective as the factory splitter. The spring is much weaker and the pawls don't engage as vigorously. I can often slide a piece backward out from under the pawls (After the blade has stopped!).

The receiver (The part under the throat plate that the splitter plugs in to.) for the splitter interferes with the throat plate when you tilt the saw blade. At 45 the rear of my throat plate was raised about 1/4 inch above the table. I emailed Excalibur asking for help. They advised me to grind away the webbing on the underside of the throat plate to provide clearence. I did so, and it works fine. But I would have preferred a solution that didn't require me to carve away on my throat plate.

Well built and effective
The MTK130 apparently will fit even veteran Delta Contractor's saws. I wanted to be sure it would go on my 15 year old unit so I emailed Excalibur to check (they did not respond). I took a chance and ordered anyway and it installed flawlessly in minutes. The instructions were really not required since the replacement parts lined up perfectly with the existing bolt holes. A minor problem did occur in that the included washers did not fit the button head bolts supplied with the installation parts. A bit if filing solved the problem but was an unnecessary waste of time. Aligning the unit was also straightforward and easily done. Contrary to another review posted here the splitter is quite compatible with the thin kerf blades in common use (Forrest, Freud, etc). Overall this is a well built, easy to install unit.

Love this spreader
Simple to install, simple to take off.Inexpensive kick-back insurance - much cheaper than the deductible from a single ER visit.Wish I would have ordered this the same day I ordered the Unisaw.

You'll have to do a bit of cutting on your zero clearance inserts, particularly if mitering.But that's easy and the added safety is well worth a few minutes on the band saw. ... Read more

Features

• Lifetime warranty
• Fits any saw with a solid cast-iron table top
• Pre-drilled to also fit virtually all 1- to 14-inch table saws
• Flip stop lets the operator choose the necessary measurement
• Can be used on the left or right side

Reviews (7)

Great quality and workmanship.
I just returned from a wood show and saw this sliding table in action.This sliding table tracks straight and level.But most impressive is how strong it is.I put two, 200 pound friends on this table and then moved the table back and forth.The table slid effortlessly, like no one was on the table.It was unbelievable.That's 400 pounds of material moving back and forth.JET makes a sliding table that will attach to most table saws but it is bulky and heavy.This thing is realatively light.The miter is excellent, easy to adjust and very easy to remove.I found that all the functions were well thought out and easy to use.For example:the frame of the sliding table is designed so that when you slide the table towards the rear there are no crossmembers in your way.Meaning that you can move your body inside the front of the table.Thus you don't find yourself leaning over the table as you push the material through.It's attention to detail like this that you will find throughout the design of this table.I would highly recommend this sliding table.

if you have the patiecne...
this thing is a PAIN to adjust, if you are not willing to put in a good day of frustration don't buy it.... but once you do it and you really crank down on the allen bolts it seems to stay put.i set mine up over two years ago and with tons of use it still is right on.
the plastic knobs that are used for moving the fence around are trash... you can find metal replacemnts through some woodworking supply stores (stuff like this can really piss you off when it breaks off while your in the middle of a project)
i pretty much don't use the 49" capacity as it is a pain to move the fence around and change all the adjustments... you can go up to around 34" if you lower the blade and then raise it up through the material, i believe 28"is the real max...
adding a micro adjust stop to the fence would be a nice touch. it is hard to move those 32nd etc...
for all it's short comings i can say i would be lost with out it. it has allowed me to take on some huge projects that would have not been possible crosscutting with a skill saw or what have you.... i don'tconsider it to be expensive, when you start looking into "real" sliding table setups and good panel saws your talking thousands....
i give it 3 stars, a mark that takes in the hassles and cheap knobs and compares it to a powermatic sliding table that costs over $10,000.....

Excalibur Sliding Table
I was looking for a precision attachment for my table saw to cut sheet goods and long stock. The excalibur table is marketed as such a product. Unfortunately, I was very dissappointed. It was an exercise in frustration and futility to properly adjust the unit and once I though I had it, it didn't take much to knock it out of alignment. Sad to say I believe this is a way overpriced piece of equipment (I almost want to say junk)and I believe your money can be better spent elsewhere. I have some ideas of how to correct this but it will require putting more effort than I care to spend on something that cost this much. I wish it was more like my Biesmeyer fence that was able to produce accurate cuts with hardly any difficulty at all. ... Read more

Subjects:  1. Saws    2. Table Saws    3. Outfeed Tables    4. (Tablesaws)   

Features

• Waterproof
• Floats in water
• Invaluable for camping, rescue and spelunking activities

Features

• Parallex Drying System