Features

• Laser cut arbor for accurate blade rotation reducing vibration and premature wear
• Laser cut stabilizer vents trap noise and vibration keeping it cool and reducing blade warp
• Laser cut heat expansion slots allow blade to expand due to heat build-up keeping the cut true and straight
• Durable micrograin titanium carbide for extreme durability, razor-sharp cuts, and long life
• Tri-metal shock resistant brazing allows carbide tips to withstand extreme impact for maximum durability

Features

• Glass smooth cuts even on cross grain
• Two wings for main cutting plus two others to cut top of profile
• No splinters or fuzz on cuts
• No splinters on top of profile

Reviews (4)

Glass Smooth, Glass Smooth, Glass Smooth
I bought this bit as part of Freuds cabinet making set. I hooked it up to a table that I have Bosch's 3 1/4hp plunge router mounted to. I forgot about the necessity of setting the speed slower to accommodate larger bits and sent the 3/4" piece of oak sailing through at the full setting. Out came a silky smooth panel. It didn't chip, sputter, kick, wobble, or even slow down the router. I wonder what it would be like if it wasn't a brand new bit with a fresh edge on it. Anyhow, I use the bit now at a slower speed setting, and make multiple passes.
Freuds cabinet making set is so well made, that their is little motivation to pick up a shaper. Shapers are known for 10,000 RPMs, thereby creating panels in a single pass that are smooth.
I have never bought a bad Freud bit. Them and Whiteside are my pride and joys. I also recommend picking up an inexpensive carbide tipped set on eBay that are imported. You can get a large selection of profiles and types for the cost of a couple of bits. When making painted moldings for example, you don't need the ultimate in sheen on the wood surface. Although with the dollar conversion and the daily monetary needs overseas, it is amazing how much quality can be produced for such a little bit of money.
Freud and Whiteside are the best, although their are several manufacturers, such as CMT and Viper that are quality bits as well. This Freud cabinet making bit is worthy of your best projects. Buy it you won't be sorry.

A "bit" dangerous
I couldn't wait to finally be able to use this expensive bit that has sat in my Raised Panel kit for years now. I followed all the rules. I purchased a high end router table and installed a 2 1/2HP variable speed router as recommended. It took about 12 passes to safely accomplish a single profile on one edge of a 10" piece of poplar. Even with the smallest adjustments, there were still some break out and kick-back. I'll go back to my nice safe vertical raised panel bit. This bit looks great, very large, and it will end up being a very expensive display piece in my router bit collection. Stick to the vertical bits. I was very disappointed in this one, and it's definitely not worth the money.

Great bit
This panel raising bit does a great job of cutting smooth and beautiful raised panels.I purchased this bit as part of a Freud cabinet door building set, and I have been thorougly impressed.The quality of all 3 of the bits is excellent.My Freud bits are the standard by which I measure all other router bits.I've worn out a cheap set of router bits and returned a medium quality set of bits due to their inferior quality.The quality of the Freud bits is well worth the cost.I will be buying more Freud panel raising bits.

The bit has a very large diameter and required some ingenuity to use in my homemade router table.

Make sure you realize that this bit cuts too deeply to allow you to make 3/4" thick panels that are flush with the frame. ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• Eight piece dovetail Incra Jig
• 1/4-inch shank
• Use on table mounted portable routers equipped with Incra jig
• Can be used with other joint making jigs or fence systems

Subjects:  1. Freud    2. (Frued)    3. Routers    4. Router Bits   

Features

• Sheer angle design for clean cutting
• Micro grain carbide for clean cut and durability
• Anti-kickback design for increased safety
• Perma shield coating keeps bit running cool
• Precision balanced for smooth chatter free cuts

Subjects:  1. Routers    2. Router Bits   

Features

• Limited lifetime warranty
• Kickback reducing design
• Computer balanced ensuring vibration-free operation
• Designed for hand-held and table-mounted routers
• Perfect for creating paneled walls and intricate moldings

Reviews (1)

What Size???
Are these for a 1/4" collet or larger?Can't buy without knowing the size! ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. Router Bits   

Features

• Kickback reducing design
• Individually computer balanced
• Precision ground for the smoothest cuts
• Covered by Freud's limited lifetime warranty

Reviews (9)

Obviously Improved And Now Flawless!!
I found this in a local store and was able to check it before ordering. The bearings are now all sized to fit the bit without the reducers and associated parts mentioned by earlier reviewers so it is definitely improved. The package has locations to hold each bearing when not in use and the cut is excellent. I have now made hundreds of cuts at various depths and it still cuts beautifully.

I think it has improved!
I read all the review in Amazon.com about this bit and hesitated to order it. I've had good luck with all the Freud blades in the past so I gave it a try despite all the bad reviews. I put the bit to test as soon as it arrived. Everything fit perfectly. Cut was very good and it is all made in Italy. There is nothing written on the bearing as one reader mentioned that it was made in China. I think may be because of the bad reviews Freud might have made improvement. One thing I still don't know it how long it will last. But looking at fit and finish it looks like a good product.

Wrong parts included - Warning: you could be next!
I wish I had read the reviews first, then I would have known to check for parts that don't fit.But I've had good luck in the past with Freud bits and thought I was getting a quality product.I discovered tonight (like many others) that the 5/16 reducers don't fit the 7/8 bearing.

Not only do they lack quality control at the plant, but how many of these are still sitting on shelves waiting to suprise the next unfortunate buyer?Ever heard of a recall or Service Bulletin?How did I happen upon one 2 years and 8 months after they knew about the problem?(See other reviews.) Or was this the fault of the retailer or distributor?

The irony of it all is I happened to "luck-up" and find it in-stock at the local lumber yard, thus avoiding the added delay and expense of ordering on-line.This particular lumber yard is14.5 miles up the road from Freud's USA Corporate office in High Point NC.I'm considering driving the extra distance and returning it directly to the manufacturer in person in addition to writing a letter. ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• Limited Lifetime Warranty
• Thick micrograin carbide tips
• Kickback reducing design
• Individually computer balanced
• Precision ground for the smoothest cuts

Reviews (2)

Good bit needs bearing
I bought this bit at the Woodworkers show 1 year ago. I used it to build one raised panel door sample and it did as expected. However I then saw other similiar Freud bits that had a bearing on it. I looked in my box for a bearing and there was none. I wish the salesman would have told me no bearing comes with the bit. I would have bought one with a bearing.

freud quality shines through
As a profesional cabinet maker, i bought this for my home shop,works well,just like most freud bits,would recomend large router,3hp or better.the only thing holding this bit back from getting five stars,is the lack of a bearing,which would make this cutter near perfect.For production shops i would recommend a shaper ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .25-inch Shank Bits    5. (1/4)    6. Router Bits   

Features

• Impervious to chemical attack
• 2-inch diameter, 3/4-inch radius, 1/2-inch shank
• Ground carbide with titanium for long life
• Anti-kickback
• Computer balanced for vibration free operation speeds over 22,000 RPM

Reviews (1)

Great quality
I'm slowly going through and replacing many of my cutting tools with Freud products.Every Freud saw blade and router bit has held its edge better than other maker's products.Freud tools cost more, but since I get to leave them on the saw longer, it's worth it to me.I wish they made drill bits! ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• Thin kerf uses less power
• Kickback reducing design
• Laser cut blade bodies and expansion slots
• Covered by Freud's limited lifetime warranty

Subjects:  1. Freud    2. (Frued)    3. Blades    4. Circular Saw Blades    5. 7.25-inch Blades    6. (1/4)   

Features

• Impervious to chemical attack
• 1/2-inch diameter, 2-inch height, 1/2-inch shank
• Ground carbide with titanium for long life
• Anti-kickback
• Computer balanced for vibration free operation speeds over 22,000 RPM

Reviews (2)

Its the real deal
As the previous reviewer said, this bit comes sharp and stays sharp.I have enjoyed super smooth cuts in flat sawn red oak, quarter sawn white oak, poplar, pine, and walnut.I can't say enough how good this bit is for flush trimming both free hand and in a table.

I highly recommend it!

Keeps going, and going, and going........
And still doesn't need sharpening!!I have used this bit a lot and it is still sharp and doesn't seem like it will ever die!!Fabulous!!5 Stars! ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• Impervious to chemical attack
• 1-1/4-inch diameter, 3/8-inch radius, 1/2-inch shank
• Ground carbide with titanium for long life
• Anti-kickback
• Computer balanced for vibration free operation speeds over 22,000 RPM

Reviews (1)

Great quality
I'm slowly going through and replacing many of my cutting tools with Freud products.Every Freud saw blade and router bit has held its edge better than other maker's products.Freud tools cost more, but since I get to leave them on the saw longer, it's worth it to me.I wish they made drill bits! ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• Impervious to chemical attack
• 1-21/32-inch diameter, 1-3/32-inch radius, 1/2-inch shank
• Ground carbide with titanium for long life
• Anti-kickback
• Computer balanced for vibration free operation speeds over 22,000 RPM

Reviews (1)

What do I do with this?
Received the Freud 99-033 Wedge and Tongue router bit as a gift. The bit doesn't leave a "tongue" cut, rather it leaves a female grove. Seems like there should be a "mate" which would be the reversecut so the tongue and grove would meet. If you need the opposite bit, thanthe ads should state the item number. If this is a one bit that does both,would be nice to receive a small booklet or picture describing the methodon how to use. ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• 2+2 raised panel bit
• Two wings to do the main cutting of the profile
• Two wings to cut the top part of the profile

Reviews (4)

Glass Smooth, Glass Smooth, Glass Smooth
I bought this bit as part of Freuds cabinet making set. I hooked it up to a table that I have Bosch's 3 1/4hp plunge router mounted to. I forgot about the necessity of setting the speed slower to accommodate larger bits and sent the 3/4" piece of oak sailing through at the full setting. Out came a silky smooth panel. It didn't chip, sputter, kick, wobble, or even slow down the router. I wonder what it would be like if it wasn't a brand new bit with a fresh edge on it. Anyhow, I use the bit now at a slower speed setting, and make multiple passes.
Freuds cabinet making set is so well made, that their is little motivation to pick up a shaper. Shapers are known for 10,000 RPMs, thereby creating panels in a single pass that are smooth.
I have never bought a bad Freud bit. Them and Whiteside are my pride and joys. I also recommend picking up an inexpensive carbide tipped set on eBay that are imported. You can get a large selection of profiles and types for the cost of a couple of bits. When making painted moldings for example, you don't need the ultimate in sheen on the wood surface. Although with the dollar conversion and the daily monetary needs overseas, it is amazing how much quality can be produced for such a little bit of money.
Freud and Whiteside are the best, although their are several manufacturers, such as CMT and Viper that are quality bits as well. This Freud cabinet making bit is worthy of your best projects. Buy it you won't be sorry.

A "bit" dangerous
I couldn't wait to finally be able to use this expensive bit that has sat in my Raised Panel kit for years now. I followed all the rules. I purchased a high end router table and installed a 2 1/2HP variable speed router as recommended. It took about 12 passes to safely accomplish a single profile on one edge of a 10" piece of poplar. Even with the smallest adjustments, there were still some break out and kick-back. I'll go back to my nice safe vertical raised panel bit. This bit looks great, very large, and it will end up being a very expensive display piece in my router bit collection. Stick to the vertical bits. I was very disappointed in this one, and it's definitely not worth the money.

Great bit
This panel raising bit does a great job of cutting smooth and beautiful raised panels.I purchased this bit as part of a Freud cabinet door building set, and I have been thorougly impressed.The quality of all 3 of the bits is excellent.My Freud bits are the standard by which I measure all other router bits.I've worn out a cheap set of router bits and returned a medium quality set of bits due to their inferior quality.The quality of the Freud bits is well worth the cost.I will be buying more Freud panel raising bits.

The bit has a very large diameter and required some ingenuity to use in my homemade router table.

Make sure you realize that this bit cuts too deeply to allow you to make 3/4" thick panels that are flush with the frame. ... Read more

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• Glue line rip joints in thick stock
• Laser cut bodies for accurate cuts
• Freud micrograin carbide for long life
• Large gullets allow for fast ripping and easy chip removal.
• Polished Steel Blade

Subjects:  1. Freud    2. (Frued)    3. Blades    4. Miter Saw Blades    5. 10-inch Blades    6. (Mitre Saws)    7. (Mitersaws)    8. (Mitresaws)    9. Table Saw Blades    10. (Tablesaws)   

Features

• Sheer angle design for clean cutting
• Micro grain carbide for clean cut and durability
• Anti-kickback design for increased safety
• Perma shield coating keeps bit running cool
• Precision balanced for smooth chatter free cuts

Subjects:  1. Routers    2. Router Bits   

Features

• Kickback reducing design
• Individually computer balanced
• Precision ground for the smoothest cuts
• Covered by Freud's limited lifetime warranty

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• Thin kerf uses less power
• Kickback reducing design
• Laser cut blade bodies and expansion slots
• Covered by Freud's limited lifetime warranty

Subjects:  1. Freud    2. (Frued)    3. Blades    4. Circular Saw Blades   

Features

• Impervious to chemical attack
• 1-3/8-inch diameter, 1/2-inch shank
• Ground carbide with titanium for long life
• Anti-kickback
• Computer balanced for vibration free operation speeds over 22,000 RPM

Subjects:  1. Freud    2. (Frued)    3. Routers    4. .50-inch Shank Bits    5. (1/2)   

Features

• Covered by Freud's limited lifetime warranty
• Drill flat bottomed holes without splintering
• Drill straight, angled and overlapping holes
• Precision machined for best results
• Right hand rotation

Subjects:  1. Drill Bits    2. Forstner Bits    3. (Drils)   

Features

• Compressed hardwood biscuits
• Box of 1000 splines

Reviews (2)

R3 Biscuits are available at Sears
Earl Staley from ky

The Sears mini-jointer is actually made by Ryobi.
Luckily, Sears still supports the product, and R3/R2/R1
biscuits are available at you local Sears store or online.

sizing biscuits
I'm looking for biscuits size R3 and can't seem to locate them as some of them pictured don't state a size. I can't use the bigger biscuits. Do you carry R3 biskets? If you do could you ID them on the web sight? Thanks Earl ... Read more

Subjects:  1. Biscuits    2. (Biscuts)    3. Plate Joiners    4. Plate Joiner Attachments    5. (Biscuit Joiners)    6. (Biscut)    7. (Cutters)