Features

• Sturdy blow-molded design
• 4" diamater connection built into the unit
• Can be positioned for connection to be either on the right or left side of machine
• Works only with the Delta 22-580 13" planer

Reviews (4)

no more clean up, planer doesn't clog anymore
It fits and does the job just fine. With this thing hooked up and the dust collection running, I can plane a bunch a stack of wood and not have to sweep, clean, and cough my lungs up when I'm done. It saves me a ton of time and keeps the garage much cleaner.

I was worried that the thin intake on it would get clogged since the planer alone tend to, but it does not. The suction from the dust collector keeps things running smoother than if the planer was doing the job alone.

The only reason I give it a 4 star rating instead of a 5 is that it must be disconnected to close up the planer. So when it's time to move the machine away to put the minivan back in the garage you've got to twiddle with some thumbscrews for a minute. Not sure how a better design could have eliminated this step, but making it go quicker with a latch or something would have been nicer.

Absolutely essential accessory for Delta 22-580 planer
Do not even try operating the Delta 22-580 planer without using this dust chute with a good dust collector attached to it. You'll create the biggest mess you can imagine and also end up with wood chips embedded in the wood you're trying to plane. It's really a shame that Delta doesn't include this accessory with its planer because it really is a vital requirement. I have been very pleased with its performance and would highly recommend it.

One of the best
This really works!I am always suspicious of the so called dust connectors. Most of them fail to collect the sawdust and leave a mess. But this is very effective at least 90 to 95% will be pulled into the dust collector. ... Read more

Features

• Adapts Delta 22-560 12-1/2-inch planer for use with a dust collector
• Allows you to maintain a cleaner, safer work environment
• Installs easily in place of existing dust chute for quick set up
• Outlet fits 4-inch dust collector hose for efficient chip collection

Reviews (7)

Much needed Part
I didn't purchase this item at the same time as I purchased my planer. What a mistake. This makes the operation of the planer so much cleaner and more effective. (I don't have to stop and clear chips out of the way.) The adapter goes to a 4" hose for a regular dust collection setup. However, with an adapter, you can use a shop vac. I used both systems and they both work extremely well. Setup was a breeze and took under five minutes. Very simple and very useful accessory.

Works great - get one.
Hooks up easy, works great, get one.

Fits easy and collects most of the chips
It took me about five minutes to put this on my planer. It gets about 99% of the dust and I'm using a 6hp, 18.6 gallon shop vac.

A hint for you if you plan on using a shop vac with this.You will need a 4 - 2 1/4 reducer.This will fit your shop vac just fine, all you need is a 2 1/2 splice and I found this at my local home center with the shop vac accessories.The 4" part of this is another story. The end of the chute is 4" and the reducer end is 4", they don't fit together they just butt up against each other and I couldn't find any kind of 4" splice.The solution for this is to use a dust collector hose but they are expensive so I bought a dryer vent hose.Normally that hose would collapse but since I'm only using to keep both of these parts together there is nothing to collapse.It works great and will save you from having to buy 20' of dust collector hose to only use 3".

PS Don't forget to get two 4" clamps to hold everything together. ... Read more

Subjects:  1. Planers    2. Planer Attachments    3. (Planners)    4. (Plainers)    5. (Surface Planers)   

Features

• Fits Delta 37-070 6-inch Bench Jointer
• High-speed steel construction for sharpness
• 2-pack

Reviews (1)

Easy replacement
These knives make replacing knives cheap and easy for the Delta 37-070K jointer - no grinding or sharpening. ... Read more

Subjects:  1. Jointers    2. Knives    3. (Knife)    4. Blades   

Features

• High-speed steel for a sharp edge
• Double-sided for twice the cutting life
• Fits Delta 22-540 12-inch Planer
• Two pack

Reviews (2)

These are reliably good!
I installed these blades as replacements on my Delta 22-540 planer and was very pleased with how sharp they were and how easy it was to install them.Once installed these knives have done a great job for me on red oak, q/s white oak, pine, and poplar.

I have owned this planer for years now and I find that these double edged knives are a great value.By flipping them over when they get dull they last me a long time.

Blades seem ok
I used one side of the blades to plane pine wood.The boards were 4 in.wide, about 1/2 inch thick and approx. 6 ft long.I planes them down toabout 3/8 in.I did about 8 pieces.Allwent well but one board had manyknots in it and it chipped the blade.Seems great for wood with few knotsin it. ... Read more

Subjects:  1. Planers    2. Knives    3. Knife    4. Blades    5. (Planners)    6. (Plainers)    7. (Surface Planers)   

Features

• High-speed steel for a sharp edge
• Double-sided for twice the cutting life
• Fits Delta 22-560 12-1/2-inch Planer--indexed for perfect alignment each time
• 2-pack

Reviews (4)

I found a lower price
Home Depothad them for $26.95. I bought all they had.

Very good value..
I've had my Delta planer for quite awhile now. In its lifetime it has had hundreds of board feet of hard and soft wood passed thru its portels. Much of this wood has been some of the hardest stuff on the planet. Mesquite, Quebracho, Vera, Mistol and white Oak just to name a few. I am on the first edge of my second set of knives. As in all planers, knife adjustment is critical, and with these knives it is as simple as tying your shoelace. Knives are sharp enough to shave with out of the pkg, and the locater holes make alignment a snap. Getting four cutting edges for this price makes the whole package a five star unit. I've had my problems with some Delta products, but this isn't one of them.Love the planer and love these knives. Highly recommend.

Blades Last a Long time and are EASY to Install
I have been running the same set of blades in my Delta 22-560 Planer for over a year. I use them to plane quarter-sawn white oak and have done about 1500 board feet. The blades are still sharp. I have not yet felt a need toflip them. I did remove them once to see how hard it would be. The locatorholes in the blades made it EASY. The tight tolerence between the holes andthe locator pins insured a minimal (less than .002")runout. The onlypossible problem is that the two blades MUST be ground exactly the same,there is no method to fine tune the alignment. This is not really a bigproblem for most sharpening services.The price is quite good, I wouldcall them a good value. ... Read more

Subjects:  1. Planers    2. Knives    3. Knife    4. Blades    5. (Planners)    6. (Plainers)    7. (Surface Planers)   

Features

• Universal design fits many brands of jointers
• Fits 6" jointers to provide proper airflow for efficient dust collection
• 4" diameter outlet for use with standard hoses

Reviews (1)

Might Be able to Make it Work
I expected a dust connector from Delta, designed for Delta 6" joiners would "bolt up" to a Delta 6" Joiner.That's not the case. Other than duct tape, I'm not sure how to install this item on the joiner. ... Read more

Subjects:  1. Vacuums    2. Dust Collectors    3. Fittings    4. (Vacumes)    5. (Vaccuums)    6. (Vaccums)    7. (Vacums)   

Features

• Fast, safe, easy to use
• Patented magnetic design holds knives in proper position for easy installation
• Allows faster and more accurate adjustment and replacement of blades

Reviews (1)

This jig is not always the best way to go
My joiner is an old 4 1/8 inch Craftsman. It runs pretty good but the knives are not easy to set. This jig seemed to be just the thing but there are two short comings I found:

1. When the jig is lined up with the knife at top dead center, the screws holding the knife in place are not accessible. So the jig has to be moved forward enough to get the knives to rotate just a bit. By this time, the knives are to high. With this set up, no amount of tweeking got both knives parallel and at the same height.

The way I tested whether the knives were parallel was to join a piece of scrape (3/4 x 3 1/2). This joined edge (3/4) was placed on the cast iron saw table and a square was used to see if the 3 1/2 side was 90 degrees to the table. I never had a test run where this was the case.

Another way I came up with was a ruler. The ruler was placed on the infeed side with the "6" on the very edge, side closest to the fence. Then the cutter was rotated until the steel blade hit the ruler. The contact point on the ruler was noted. In my case, this was about 7 1/16 on the ruler. Then the ruler was moved to the other end of the knive and the process was repeated. Most of the time I could not detect a difference so maybe my machine is the real problem.

2. The magnets were not strong enough to pull up the knives every time. Sure, the jig would stick to the cast iron table but the knives would often stay put. I used a spare rare earth magnet to pull the knives up to the jig magnets. Once in place, the knives would stay put most of the time. I ended up making another little tool with the magnet screwed to a scrap piece of wood. This was used to pull the knives up to the jig magnet.

So, I'll keep the tool as it came by way of UPS and sending it back would not be free. But I would be very careful about recommending the jig. ... Read more

Subjects:  1. Jigs    2. Knife-Setting Jigs   

Features

• Replaces worn drive belt to maintain peak performance
• Original equipment replacement for an exact fit
• Installs easily on existing pulleys
• Fits Delta 22-540 12" planer

Subjects:  1. Planers    2. Planer Attachments    3. (Planners)    4. (Plainers)    5. (Surface Planers)   

Features

• Fits Delta 37-190 and 37-195 Jointers
• High-speed, case hardened steel construction for sharpness
• 3-pack

Reviews (1)

Knives for 37-190 and 195 Jointers
If you purchase either of the 6" Delta Jointers, I would highly recommend these knives.This way when your knives are damaged you have another set ready to go while you have the others sharpened. ... Read more

Subjects:  1. Jointers    2. Knives    3. (Knife)    4. Blades   

Features

• High-speed steel for a sharp edge
• Fits Delta 22-675, 22-676, 22-680, and 22-681 15-inch Planers
• Three pack

Subjects:  1. Planers    2. Knives    3. Knife    4. Blades    5. (Planners)    6. (Plainers)    7. (Surface Planers)   

Features

• Universal design fits many brands of jointers
• Fits 8" jointers to provide proper airflow for efficient dust collection
• 4" diameter outlet for use with standard hoses

Subjects:  1. Vacuums    2. Dust Collectors    3. Fittings    4. (Vacumes)    5. (Vaccuums)    6. (Vaccums)    7. (Vacums)   

Features

• Fits Delta 37-350 DJ-20 Jointer and 37-380 Professional Jointer
• High-speed steel construction for sharpness
• 3-pack

Reviews (1)

Delta Knock-off's
I ordered the Delta 37-365X Jointer and a set of knives for back up. When the knives arived, they were not in a Delta box and Delta's name/part number was not printed on the knives. I call Amazon and requested a second set, no-luck, same set was sent again. I returned the knives, and ordered a set from Delta direct. I feel, to keep equpment running safe and trouble free, buy orgenal parts only, not copies. ... Read more

Subjects:  1. Jointers    2. Knives    3. (Knife)    4. Blades   

Features

• Increase the safety of jointing operations
• Molded handle provides comfortable grip
• Rubber bottom pad grips workpiece surface

Subjects:  1. Jigs    2. Featherboards    3. (Feather Boards)    4. Jointers    5. Jointer Attachments   

Features

• Replaces worn drive belt to maintain peak performance
• Original equipment replacement for an exact fit
• Installs easily on existing pulleys
• Fits TP400LS, 22-565, 22-560, and 22-580 Delta planers

Subjects:  1. Planers    2. Planer Attachments    3. (Planners)    4. (Plainers)    5. (Surface Planers)   

Features

• Fast, safe, easy to use
• Patented magnetic design holds knives in correct alignment for easy installation
• Accurate, faster knife adjustment or replacement for less down time

Subjects:  1. Planers    2. Knives    3. Knife    4. Blades    5. (Planners)    6. (Plainers)    7. (Surface Planers)   

Features

• Simplifies planer adjustments
• Accurate 10 within .001" tolerance
• Magnetic base for stability
• Rotating dial for versatility and ease of set up

Subjects:  1. Planers    2. Planer Attachments    3. (Planners)    4. (Plainers)    5. (Surface Planers)   

Features

• Installs easily for quick set up
• Connects to a dust collector for a cleaner, safer work environment
• Fits Delta 22-657, 22-676, 22-680, and 22-681 planers

Subjects:  1. Vacuums    2. Dust Collectors    3. Fittings    4. (Vacumes)    5. (Vaccuums)    6. (Vaccums)    7. (Vacums)    8. Planers    9. Planer Attachments    10. (Planners)    11. (Plainers)    12. (Surface Planers)   

Features

• Fits Delta 37-154 6-inch Precision Jointer
• High-speed steel construction for sharpness
• 3-pack

Subjects:  1. Jointers    2. Knives    3. (Knife)    4. Blades